Australian Made Logo

Quality Paint at Sensible Prices

"Brinlay's Premium Range of Paints are regularly tested against all leading paint brands to ensure equal or better quality, but cost much less"
Read More

Í

65 Waratah Street
Kirrawee NSW 2232
Ph: 02 9521 8777
Fax: 02 9521 4797

Interior

Interior Paints

Exterior

Exterior Paints

Varnishes

Sealers

Sealers

Trim Colours

Trim Colours

Wood Stains

Wood Stains

Premium 100% Acrylic Sealer Undercoat

Premium 100% Acrylic Sealer Undercoat

DESCRIPTION

Brinlay Acrylic Sealer Undercoat is a flat finish, 100% Acrylic paint, which seals and undercoats plasterboard, masonry and interior timber in one coat. It is formulated to give excellent grain filling, and a hard finish for easy sanding. Short drying and re-coating time, this undercoat may be re-coated with solvent or water based paints. It is suitable for use as an undercoat on surfaces previously finished with enamel, provided all gloss is removed by thorough sanding.

SUITABLE PAINTING SURFACES

All exterior/interior surfaces where an undercoat is required for adhesion, sandability and coverage.

GENERAL DATA

Gloss Selection Guide
Flat.

Colour: White.

Application: Stir well with a broad paddle. Brush, roller or spray. Provide adequate ventilation. Temperature should be above 10ºC. Early exposure to steam, overnight dew, rain or hosing may result in damage or removal of the coating.

Coverage: Approx. 14 – 16 sq. metres per litre. On rough or highly absorbent surfaces this figure may be reduced.

Thinning: Up to 100 ml of clean water per litre for spraying or application to very porous surfaces.

Drying: Touch dry in 30 minutes. Recoat 2 hours on a day of 25ºC and 50% relative humidity, but will be longer in adverse conditions.

Clean Up: Water and detergent. Dried spots can be removed using General Purpose Thinners.

SURFACE PREPARATION

Previously Painted Surfaces:

  • Ensure all surfaces are cleaned of dirt, dust, powder, grease, oil, smoke stains, cooking residues, polishes and materials detrimental to the finish and adhesion of the new paints by washing with water and detergent or sugar soap (as appropriate), rinse clean any residues.
  • Sterilise mould or moss with bleach or Brinlay Fungicidal Wash.
  • Fill surface holes with an appropriate filler and sand to match existing surface. Sand all gloss and semi-gloss paints to a flat look. Remove flaked, cracked, peeling and poorly adhered unsound paints which should be tested as follows:
  • Test surface at random by cutting a small cross (X) through the existing paints. Apply and press down firmly a piece of sticky tape over the cut. Hold the end of the tape and rip off. If the paint is removed, check other areas. Paints consistently failing test or, if any doubt to their adhesion, should be completely removed.
  • Powdering paints or kalsomine surfaces should be washed down with sugar soap and have one coat of Brinlay Binder & Conditioner applied before applying the undercoat.

Previously painted surfaces: Remove all loose and flaking paint by stripper, flame or hot air gun or mechanical means. Sand the area well, feathering off edges of remaining paints. Apply Brinlay Wood Primer.

New Timber: Suitable for all seasoned timber which is free from dirt, wax, mildew etc. Sand lightly before application and between additional coats. Do not leave for extended periods prior to applying finishing coats.

HEALTH AND SAFETY

For detailed information, refer to the product label and the current Material Safety Data Sheet available through Brinlay Paints.

Flammability: This product is non-flammable. Store and use away from sources of heat and ignition.

Toxicity: Non-toxic, environmentally friendly, lead free and non-hazardous.

TRANSPORT AND STORAGE

Sizes:
1 litre, 2 litre, 4 litre, 10 litre and 20 litre
Dangerous Goods Class:
N/A
Flashpoint:
N/A
UN:
N/A
Packaging Group:
N/A